2345彩票代理歡迎您的到來!

2345彩票代理(蘇州福盛泰物流設備有限公司東北辦事處)
您現在的位置:首頁>>門封,卸貨平台新聞 >> 「沈陽廠房機械門封」海綿門封和機械門封的優勢對比

    「沈陽廠房機械門封」海綿門封和機械門封的優勢對比

    作者:沈陽機械門封定做   發布時間: 2019/7/3 15:42:44



  • 「沈陽廠房機械門封」海綿門封和機械門封的優勢對比



    The Advantages of Sponge Door Seal and Mechanical Door Seal in Shenyang Workshop


     

    工業門的高密度海綿門封與機械門罩對比在于,擠壓式門封更能合理地填充封閉式大貨車與工作領域間的縫隙,并且成本費用較低



    Comparing the high density sponge door seal with the mechanical door cover, the extrusion door seal can fill the gap between the closed truck and the working field more reasonably, and the cost is lower.

     

    沈陽機械門封價格





    但與此同時,門封的厚度會引貨台門洞的淨寬縮減,偶爾會影響托闆流暢地出入庫大貨車。



    However, at the same time, the thickness of the door seal will reduce the net width of the entrance of the cargo platform, occasionally affecting the smooth access of pallets to and from the warehouse truck.



    還有在其它情形下,大貨車尾端有外伸的托闆時,門封的運用會面臨不良影響。



    In other cases, when the truck rear end has an extended bracket, the use of door seals will face adverse effects.



    工作領域門寬大于2.8米或高于3.0米時,不可以接納門封。



    Door seals are not acceptable when the width of the work area door is larger than 2.8 meters or higher than 3.0 meters.

     

    沈陽海綿門封定做




    工業門門封的封墊内間隔寬度計劃方案成2.2- 2.3米寬度為好,門封可适應大部分的大貨車。



    The width of the gap in the gasket of industrial door seals is planned to be 2.2-2.3 meters wide. The door seals can be adapted to most large trucks.



    貨車工作領域門寬于2.3米時,需接納斜角封墊。



    When the truck working area door is wider than 2.3 meters, inclined gaskets should be accepted.



    門封上端封墊的邊沿底需低于大貨車後頂部非常少8公分。



    The edge and bottom of the top sealing pad of the door seal should be very little 8 cm below the top of the rear of the truck.



    門封上端封墊可按照大貨車高度的需要而上下調整。



    The top sealing pad of the door seal can be adjusted up and down according to the height of the truck.



    領域門較高且大貨車高度條件過大時,接納調整的垂簾形成蓬式門封替代上端封墊。



    When the field door is high and the height condition of the truck is too large, the adjustable drapes are adopted to form a canopy door seal instead of the upper seal.



    「沈陽廠房機械門封」海綿門封和機械門封的優勢對比



    The Advantages of Sponge Door Seal and Mechanical Door Seal in Shenyang Workshop




    挑選擠壓式海綿門封的常見問題:



    Common problems in selecting extruded sponge door seals:



    1.封墊對牆面造成的壓力約為每米120千克。斜角封墊約為一半。



    1. The pressure on the wall caused by the cushion is about 120 kilograms per meter. The bevel gasket is about half.



    2.房屋建築牆面到防撞膠平面非常少要有10厘米的間隙,為門封擠壓後的壁厚留有餘地。



    2. There is very little gap of 10 centimeters between the wall of building and the collision-proof glue plane, leaving room for the wall thickness after the door seal is extruded.



    3.封墊的厚度應高于防撞膠平面10到20厘米,高過15厘米更是為宜。



    3. The thickness of the gasket should be 10 to 20 centimeters higher than the collision-proof glue plane, and 15 centimeters higher is more appropriate.



    4.裝卸區路面傾斜度超過2%時,應接納錐壯封墊。




    4. When the gradient of the road surface in the loading and unloading area exceeds 2%, the conical seal shall be adopted.



    傾斜度每提升一個百分之一,封墊頂端厚度比底部厚度應小2.5厘米。



    The top thickness of the gasket should be 2.5 centimeters less than the bottom thickness for every 1% increase in the inclination.




     

2345彩票代理
(蘇州福盛泰物流設備有限公司
東北辦事處)
電話:024-31081023
聯系人:于經理
網址:www.ilid.com.cn
版權所有:2345彩票代理
(蘇州福盛泰物流設備有限公司東北辦事處)
  
電話:024-31081023
聯系人:于經理
百度地圖 - 網站地圖 -